Search found 592 matches

Return to advanced search

Re: You are new here? Say a short "hello" to all other membe

Hello , I'm Gilles . I build a 2DOF Simulator with 2 BigWorm gear motor and VM110 + Saberbooth. I would like to thanks all the X Simer community for its support and ideas for our big adventure building a simulator. Special thanks to Thanos and Sirnoname for his passion and for sharing all what they ...
by vicpopo
Thu 26. Apr 2012, 22:23
 
Forum: New users start here - FAQ
Topic: You are new here? Say a short "hello" to all other members!
Replies: 1735
Views: 299438

Re: Thanos AMC1.6 USB Motion Controller

Kp setting : I tried with an another PC and the problem is always here.You can change the Kp setting but it takes time, you have to make several tries for entering new values. Hi Gilles, I just updated the first page with new firmware that allow you to change KP settings directly from x-sim convert...
by vicpopo
Wed 18. Jul 2012, 18:51
 
Forum: Controllers and Drivers Projects
Topic: Thanos AMC1.6 USB 2DOF Motion Controller
Replies: 441
Views: 146721

Re: Thanos AMC1.6 USB Motion Controller

Hi Thanos , Ok right it works ,with your video I better understood how to change Kp settings! I fixed the kp value for the wiper motor to 1 !! It's the value that give me the minimum motor shaking and when I test the motor positioning quickly with the slider that give not to high rebound eventhougt ...
by vicpopo
Wed 18. Jul 2012, 21:35
 
Forum: Controllers and Drivers Projects
Topic: Thanos AMC1.6 USB 2DOF Motion Controller
Replies: 441
Views: 146721

Re: Thanos AMC1.6 USB Motion Controller

Hi, Gilles. I think (and may be Thanos thinks like me :D ) there is one easy way to search optimum Kp value for your system: to use alternative software complex from ALE ( it's me ;) ). If you will use my firmware with special software 'xSimCtrl', you will see GRAPHICAL response of your system to s...
by vicpopo
Wed 18. Jul 2012, 21:43
 
Forum: Controllers and Drivers Projects
Topic: Thanos AMC1.6 USB 2DOF Motion Controller
Replies: 441
Views: 146721

Re: PC setup

Thanks Thanos for your reply. Its re-assuring that a second computer is not a requirement and I appear to have enough computing power available, but it sounds as if a crash of the computer might result in a real crash of the simulator. I guess that's why an emergency stop switch is a good thing to ...
by vicpopo
Thu 19. Jul 2012, 20:53
 
Forum: Forum & Website
Topic: PC setup
Replies: 16
Views: 3084

Re: Thanos AMC1.6 USB Motion Controller

Hi, Gilles I 'm a little bit squary using your software ... I understand your concern. No problem. Regards. ALE Hi Prilad,Hi Thanos I tested ale's firmware with xsim and I didn't burn any mofset :P But I tested with Prilad software xsimctrlv2.2(without xsim running) and it doesn't work (problem I s...
by vicpopo
Fri 20. Jul 2012, 01:22
 
Forum: Controllers and Drivers Projects
Topic: Thanos AMC1.6 USB 2DOF Motion Controller
Replies: 441
Views: 146721

Re: Settings for k8055 and Sabertooth

Hi Gillies Like i said in my orginal post,that i have tried 3 different projects from 3 different people..Adbgg was 1 of them and found his easier to understand but in the output section of converter he has not used anything in the "OUTPUT AXIS DIRECT" where the other 2 i tried to follow ...
by vicpopo
Sun 22. Jul 2012, 10:32
 
Forum: Controllers and Drivers
Topic: Settings for k8055 and Sabertooth
Replies: 9
Views: 3141

Re: Information on CKAS T2s motion platform

by vicpopo
Mon 30. Jul 2012, 21:51
 
Forum: Motion simulator building Q&A
Topic: Information on CKAS T2s motion platform
Replies: 5
Views: 2350

Possibly the future in motion controllers?

Hi Roadster2, It isn't maybe the good topic to discuss about this.The moderators should be put it in an another topic. I bought 2 single h-bridge hd02 I believe and I burned the 2! I bought this dual but I don't know if I will test it with these motors. The ebayseller did me 30% off on it because I ...
by vicpopo
Mon 10. Sep 2012, 16:00
 
Forum: Controllers and Drivers
Topic: Possibly the future in motion controllers?
Replies: 71
Views: 16988

Re: My 2DOF simulator with sew eurodrive geared motors

Hi, I will check this point whis this simulator .I don't have termal driving in these motors , if the temperature will go up 70 °C I will put fans on the motors .It's also dangerous if someone touch them. When I look at ckas configurations , the old one have fans fitted on the motors and the new one...
by vicpopo
Wed 24. Oct 2012, 17:02
 
Forum: Motion simulator Projects in progress
Topic: My 2DOF simulator with sew eurodrive geared motors
Replies: 77
Views: 27635
Next

Return to advanced search